Flashen Coolstream Shiner funktioniert nicht

[cycoboy]

Guten Tag,

ich habe gerade versucht anhand Ihrer Anleitung
(viewtopic.php?f=48&t=135)
meine Coolstream (Shiner) neu zu flashen, da sie nicht mehr bootet.
Wenn ich den Flashvorgang starte schreibt sie in der Konsolenzeile folgendes:

Emergency update from usb
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uldr.bin

** Unable to read "uldr.bin" from usb 0:1 **
** Skipping uldr.bin **
reading u-boot.bin

** Unable to read "u-boot.bin" from usb 0:1 **
** Skipping u-boot.bin **
reading env.bin

** Unable to read "env.bin" from usb 0:1 **
** Skipping env.bin **
reading vmlinux.ub.gz

** Unable to read "vmlinux.ub.gz" from usb 0:1 **
** Skipping vmlinux.ub.gz **
reading rootfs.arm.jffs2.nand

** Unable to read "rootfs.arm.jffs2.nand" from usb 0:1 **
** Skipping rootfs.arm.jffs2.nand **
reading rootfs1.arm.jffs2.nand

** Unable to read "rootfs1.arm.jffs2.nand" from usb 0:1 **
** Skipping rootfs1.arm.jffs2.nand **
reading var.arm.jffs2.nand

** Unable to read "var.arm.jffs2.nand" from usb 0:1 **
** Skipping var.arm.jffs2.nand **
resetting ...


Anschließend bootet sie das alte, kaputte image.

Haben Sie eine Idee, warum Sie die Dateien nicht lesen kann/will?

Liebe Grüße

Cycoboy

[cycoboy]

Hallo zusammen,

ich bin einen Schritt weiter gekommen.
Jedoch bleibt die Box beim booten bei einem Punkt "hängen". Habt Ihr eine Ahnung, wieso?

Der Log lautet wie folgt:

Starting Microloader ASM built on окт 08 2015 09:37:26...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Chip: SHINER-IP
Found Internal Ethernet PHY on GMAC0....
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
MMC:No device found
BOX MAC OK!
BOX: Type: TRINITY Rev: 84700102
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 721 ms since POR
--------------------------------------------------------------------------------
| U-Boot 2009.08-00067-gebbd4b2 (Apr 03 2015 - 16:35:07) CST HDx |
|------------------------------------------------------------------------------|
| Chipset information |
| Vendor: NXP Type: Shiner-IP Revision: M1 Fuses: 0015716D |
|------------------------------------------------------------------------------|
| Clock information |
| *** not available yet *** |
|------------------------------------------------------------------------------|
| Frontpanel information |
| Vendor: CST Version: 5.1 Display: none |
|------------------------------------------------------------------------------|
| Memory configuration |
| Start | End | Type | Description |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 0FFFFFFF | RAM | System main memory bank #0 (256M) |
| 20000000 | 2FFFFFFF | RAM | System main memory bank #1 (256M) |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 ( 4M / 64K x 64) |
*** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND | Toshiba NAND 512MiB 3,3V 8-bit |
|------------------------------------------------------------------------------|
| Network configuration |
| MAC: LIP 6300 address: 00-C5-5C-1F-3F-29 |
--------------------------------------------------------------------------------

Hit any key to stop autoboot: 0

SFC read: offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: NI Apollo Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2969776 Bytes = 2.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.10.93 (neutrino-images@nisrv) (gcc version 4.9.4 (crosstool-NG crosstool-ng-1.23.0-36-g1dbb06f2) ) #1 SMP Thu Oct 19 17:42:14 CEST 2017
[ 0.000000] CPU: ARMv7 Processor [411fc091] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Entropic Apollo STB Platform with FDT, model: CoolStream HD2 Apollo STB
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Early platform io descriptors mapping...
[ 0.000000] PERCPU: Embedded 7 pages/cpu @80908000 s5952 r8192 d14528 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 246988k/246988k available, 277300k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x80671bdc (6567 kB)
[ 0.000000] .init : 0x80672000 - 0x806a1740 ( 190 kB)
[ 0.000000] .data : 0x806a2000 - 0x806e3da0 ( 264 kB)
[ 0.000000] .bss : 0x806e3da0 - 0x806ff438 ( 110 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:388
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] smp_twd: clock not found -2
[ 0.000000] Unable to get timer clock. Assuming 50Mhz input clock.
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000] stb-timer: system timer (irq = 58, rate 50000000)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.253196] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 0.342785] pid_max: default: 32768 minimum: 301
[ 0.347632] Mount-cache hash table entries: 512
[ 0.354182] CPU: Testing write buffer coherency: ok
[ 0.359318] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.364965] Setting up static identity map for 0x803de4b8 - 0x803de510
[ 0.371513] L310 cache controller enabled
[ 0.375436] l2x0: 8 ways, CACHE_ID 0x410004c4, AUX_CTRL 0x32421001, Cache size: 131072 B
[ 0.384159] Brought up 1 CPUs
[ 0.387040] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[ 0.393367] CPU: All CPU(s) started in SVC mode.
[ 0.398732] devtmpfs: initialized
[ 0.408918] NET: Registered protocol family 16
[ 0.414008] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.545394] GMAC0: active interface is 1
[ 0.549255] ChipID=0x3 ChipRevID=0x2
[ 0.552958] nx_dmac: Registered with 8 channels
[ 0.562277] bio: create slab <bio-0> at 0
[ 0.566801] GPIO: base febd5000 (phys e06d5000)
[ 0.571512] GPIO: base feb69000 (phys e0669000)
[ 0.576449] SCSI subsystem initialized
[ 0.580587] usbcore: registered new interface driver usbfs
[ 0.586005] usbcore: registered new interface driver hub
[ 0.591406] usbcore: registered new device driver usb
[ 0.596452] pps_core: LinuxPPS API ver. 1 registered
[ 0.601337] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.610409] PTP clock support registered
[ 0.616113] Switching to clocksource timer_us
[ 0.627291] NET: Registered protocol family 2
[ 0.632478] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.639513] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.645959] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.652273] TCP: reno registered
[ 0.655412] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.661252] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.667722] NET: Registered protocol family 1
[ 0.672331] RPC: Registered named UNIX socket transport module.
[ 0.678143] RPC: Registered udp transport module.
[ 0.682847] RPC: Registered tcp transport module.
[ 0.687474] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.694058] PM: STB Platform power mgmt initialization.
[ 0.814996] cfg80211: Calling CRDA to update world regulatory domain
[ 0.822152] bounce pool size: 64 pages
[ 0.831994] NFS: Registering the id_resolver key type
[ 0.836997] Key type id_resolver registered
[ 0.841143] Key type id_legacy registered
[ 0.845083] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.851516] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.858869] msgmni has been set to 482
[ 0.863619] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.870968] io scheduler noop registered
[ 0.874790] io scheduler deadline registered
[ 0.879215] io scheduler cfq registered (default)
[ 0.884253] e06e2000.serial: ttyS0 at MMIO 0xe06e2000 (irq = 47) is a uart-ip3106
[ 0.895668] loop: module loaded
[ 0.899122] ahci-stb e0638000.sata: unable to find phy
[ 0.904260] SATA: Adjusting los_lvl (rd_val=0x8a46, wr_val=0x8ae6)
[ 0.910345] SATA: Adjusting rx_term_en0/1 (rd_val=0x2750275, wr_val=0x2770277)

[mirz]

ich vermute, die Box ist hin.

Wenn man nach "SATA: Adjusting" suchst, dann findet man einige Wiederbelebungsversuche; meist ohne Erfolg.

[cycoboy]

Guten Abend,

Vielen Dank für die Information.
Dann geht Sie jetzt in die Tonne.

Liebe Grüße und schönen Abend

[Don de Deckelwech]

Hi,
nunja, schade, dass dich niemand unterstützt hat, evtl war niemand online, der dir helfen konnte, ich jedenfalls war gestern garnicht hier. Dies ist aber eher die Ausnahme, normalerweise werden Sie hier geholfen...

Zur Box: wie ist denn die Vorgeschichte der Box, also was war passiert? Als du dann iwann erfolgreich flashen konntest, hast du da auch eine leere env.bin mit auf dem Stick gehabt?
Da du ja den Kernel aus dem letzten Release-Image verwendet hast (laut der Anleitung halt auch völlig richtig!), würde ich es an deiner Stelle auch einfach nochmal mit dem aktuellen Nightly-Kernel probieren: https://www.neutrino-images.de/neutrino ... inux.ub.gz . Vllt hast du ja noch Lust das kurz zu testen...

Ciao,
DdD.

[mimisiku]

Im Log steht doch Apollo HD2? Das ist dann doch kein Shiner?

[vanhofen]

Code: Alles auswählen

| Chipset information |
| Vendor: NXP Type: Shiner-IP Revision: M1 Fuses: 0015716D

Es ist ein Shiner-Chipsatz. Das Apollo-Image wird darauf nicht booten.

[stefanx]

ja, ja, da werden immer wieder diese "Seriennamen" verwendet und nicht mit dem richtigem Modellnamen und deren Ausführung bezeichnet und dann die falschen Images oder Herstellungsdateien verwendet.
Das hatte mich bei der Link als einen der Ersten betroffen, jedoch ich habe die dann nach vielen Versuchen und Stunden wieder hinbekommen.
Jedoch habe ich später eine bekommen, da war nichts mehr zu machen, einfach tot.

[cycoboy]

Guten Abend zusammen,

Ich werde es später noch mit dem nightly testen und berichten.

Liebe Grüße und danke für den Tipp

Cycoboy

[cycoboy]

Achso und zur Vorgeschichte:

Wie jeden Abend ausgeschaltet, Kippschalter umgelegt, nächste Woche angemacht und Boot schleife.

[mirz]

ich bin anscheinend nicht mehr auf dem Laufenden.
Shiner ist doch ein apollo chip, oder? Es gibt doch bei der Trine nur apollo (shiner) und kronos.

Oder ist hier das Image der Tank (Apollo) gemeint, das geflasht wurde?

[cycoboy]

Soooo nun habe ich das Nigthly genommen und das selbe Problem liegt leider vor.. :/
Liegen noch Ideeen vor?

Liebe Grüße

[cycoboy]

Ich hatte in einem ähnlichen Post gelesen, dass die folgenden zwei Dateien ebenfalls mit neu geflasht wurden. Leider finde ich diese nirgends zum Download.
Kann mir diese jemand bereitstellen?

- uldr.bin (Loader)
- u-boot.bin (u-Boot)

Liebe Grüße

[Don de Deckelwech]

Hi,
dort: viewtopic.php?f=48&t=136 ganz unten als Anhang.

Und zeig doch dann auch mal das Log vom Flashen.

Ciao,
DdD.

[cycoboy]

Danke für die Info.

Ich habe nun mit den Dateien neu geflasht, jedoch bleibt er an der selben Stelle hängen.
Ich hänge nun alles an, vom Flash bis zum booten anschließend.

Hit any key to stop autoboot: 1

Starting Microloader ASM built on окт 08 2015 09:37:26...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Chip: SHINER-IP
Found Internal Ethernet PHY on GMAC0....
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
MMC:No device found
BOX MAC OK!
BOX: Type: TRINITY Rev: 84700102
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 721 ms since POR
--------------------------------------------------------------------------------
| U-Boot 2009.08-00067-gebbd4b2 (Apr 03 2015 - 16:35:07) CST HDx |
|------------------------------------------------------------------------------|
| Chipset information |
| Vendor: NXP Type: Shiner-IP Revision: M1 Fuses: 0015716D |
|------------------------------------------------------------------------------|
| Clock information |
| *** not available yet *** |
|------------------------------------------------------------------------------|
| Frontpanel information |
| Vendor: CST Version: 5.1 Display: none |
|------------------------------------------------------------------------------|
| Memory configuration |
| Start | End | Type | Description |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 0FFFFFFF | RAM | System main memory bank #0 (256M) |
| 20000000 | 2FFFFFFF | RAM | System main memory bank #1 (256M) |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 ( 4M / 64K x 64) |
*** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND | Toshiba NAND 512MiB 3,3V 8-bit |
|------------------------------------------------------------------------------|
| Network configuration |
| MAC: LIP 6300 address: 00-C5-5C-1F-3F-29 |
--------------------------------------------------------------------------------

Hit any key to stop autoboot: 1
Emergency update from usb
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uldr.bin

55560 bytes read

SFC erase: offset 0x0, size 0x40000
OK

SFC write: offset 0x0, size 0x40000
262144 bytes written: OK
reading u-boot.bin

347008 bytes read

SFC erase: offset 0x40000, size 0x80000
OK

SFC write: offset 0x40000, size 0x80000
524288 bytes written: OK
reading env.bin

0 bytes read

SFC erase: offset 0xc0000, size 0x20000
OK

SFC write: offset 0xc0000, size 0x20000
131072 bytes written: OK
reading vmlinux.ub.gz

2970408 bytes read

SFC erase: offset 0x100000, size 0x300000
OK

SFC write: offset 0x100000, size 0x300000
3145728 bytes written: OK
reading rootfs.arm.jffs2.nand

50936692 bytes read

NAND erase: device 0 offset 0x0, size 0x10000000
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
Erasing at 0xffe0000 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0x3093b74
50936692 bytes written: OK

** Invalid boot device **
** Skipping rootfs1.arm.jffs2.nand **

** Invalid boot device **
** Skipping var.arm.jffs2.nand **
resetting ...


Starting Microloader ASM built on окт 08 2015 09:37:26...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Chip: SHINER-IP
Found Internal Ethernet PHY on GMAC0....
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
MMC:No device found
BOX MAC OK!
BOX: Type: TRINITY Rev: 84700102
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 717 ms since POR
--------------------------------------------------------------------------------
| U-Boot 2009.08-00067-gebbd4b2 (Apr 03 2015 - 16:35:07) CST HDx |
|------------------------------------------------------------------------------|
| Chipset information |
| Vendor: NXP Type: Shiner-IP Revision: M1 Fuses: 0015716D |
|------------------------------------------------------------------------------|
| Clock information |
| *** not available yet *** |
|------------------------------------------------------------------------------|
| Frontpanel information |
| Vendor: CST Version: 5.1 Display: none |
|------------------------------------------------------------------------------|
| Memory configuration |
| Start | End | Type | Description |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 0FFFFFFF | RAM | System main memory bank #0 (256M) |
| 20000000 | 2FFFFFFF | RAM | System main memory bank #1 (256M) |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 ( 4M / 64K x 64) |
*** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND | Toshiba NAND 512MiB 3,3V 8-bit |
|------------------------------------------------------------------------------|
| Network configuration |
| MAC: LIP 6300 address: 00-C5-5C-1F-3F-29 |
--------------------------------------------------------------------------------

Hit any key to stop autoboot: 0

SFC read: offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: NI Apollo Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2970344 Bytes = 2.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.10.93 (neutrino-images@nisrv) (gcc version 6.3.1 20170109 (crosstool-NG crosstool-ng-1.23.0-36-g1dbb06f2) ) #1 SMP Sat Aug 25 03:53:51 CEST 2018
[ 0.000000] CPU: ARMv7 Processor [411fc091] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Entropic Apollo STB Platform with FDT, model: CoolStream HD2 Apollo STB
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Early platform io descriptors mapping...
[ 0.000000] PERCPU: Embedded 7 pages/cpu @80906000 s5952 r8192 d14528 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 247000k/247000k available, 277288k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x8066fdc4 (6560 kB)
[ 0.000000] .init : 0x80670000 - 0x8069f740 ( 190 kB)
[ 0.000000] .data : 0x806a0000 - 0x806e1d60 ( 264 kB)
[ 0.000000] .bss : 0x806e1d60 - 0x806fd424 ( 110 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:388
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] smp_twd: clock not found -2
[ 0.000000] Unable to get timer clock. Assuming 50Mhz input clock.
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000] stb-timer: system timer (irq = 58, rate 50000000)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.253950] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 0.342792] pid_max: default: 32768 minimum: 301
[ 0.347636] Mount-cache hash table entries: 512
[ 0.354192] CPU: Testing write buffer coherency: ok
[ 0.359325] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.364972] Setting up static identity map for 0x803dd018 - 0x803dd070
[ 0.371531] L310 cache controller enabled
[ 0.375451] l2x0: 8 ways, CACHE_ID 0x410004c4, AUX_CTRL 0x32421001, Cache size: 131072 B
[ 0.384173] Brought up 1 CPUs
[ 0.387046] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[ 0.393370] CPU: All CPU(s) started in SVC mode.
[ 0.398737] devtmpfs: initialized
[ 0.408987] NET: Registered protocol family 16
[ 0.414066] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.544740] GMAC0: active interface is 1
[ 0.548595] ChipID=0x3 ChipRevID=0x2
[ 0.552297] nx_dmac: Registered with 8 channels
[ 0.561588] bio: create slab <bio-0> at 0
[ 0.566109] GPIO: base febd5000 (phys e06d5000)
[ 0.570816] GPIO: base feb69000 (phys e0669000)
[ 0.575753] SCSI subsystem initialized
[ 0.579865] usbcore: registered new interface driver usbfs
[ 0.585349] usbcore: registered new interface driver hub
[ 0.590697] usbcore: registered new device driver usb
[ 0.595751] pps_core: LinuxPPS API ver. 1 registered
[ 0.600641] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.609703] PTP clock support registered
[ 0.615418] Switching to clocksource timer_us
[ 0.626469] NET: Registered protocol family 2
[ 0.631641] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.638671] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.645120] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.651438] TCP: reno registered
[ 0.654582] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.660422] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.666888] NET: Registered protocol family 1
[ 0.671500] RPC: Registered named UNIX socket transport module.
[ 0.677321] RPC: Registered udp transport module.
[ 0.682020] RPC: Registered tcp transport module.
[ 0.686651] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.693220] PM: STB Platform power mgmt initialization.
[ 0.819159] cfg80211: Calling CRDA to update world regulatory domain
[ 0.826317] bounce pool size: 64 pages
[ 0.836175] NFS: Registering the id_resolver key type
[ 0.841217] Key type id_resolver registered
[ 0.845300] Key type id_legacy registered
[ 0.849288] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.855723] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.863097] msgmni has been set to 482
[ 0.867827] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.875173] io scheduler noop registered
[ 0.878996] io scheduler deadline registered
[ 0.883443] io scheduler cfq registered (default)
[ 0.888437] e06e2000.serial: ttyS0 at MMIO 0xe06e2000 (irq = 47) is a uart-ip3106
[ 0.899850] loop: module loaded
[ 0.903398] ahci-stb e0638000.sata: unable to find phy
[ 0.908444] SATA: Adjusting los_lvl (rd_val=0x8a46, wr_val=0x8ae6)
[ 0.914607] SATA: Adjusting rx_term_en0/1 (rd_val=0x2750275, wr_val=0x2770277)

[Don de Deckelwech]

Hi,
tja, leider auch ohne Erfolg, scheint wirklich was mit der Hardware zu sein. Keine Ahnung, ob ein Hardware-Spezi da noch eine Idee hat, mir fällt ausser so Voodoo àla die Platine in den Backofen zum "Nachlöten" packen auch nix mehr ein... Vorher aber mal bei offener Box mit nem Fön testen, ob etwas Temperatur vllt am Verhalten was ändert, dann wäre das evtl einen verzweifelten Versuch wert...

Hattest du die Box mal aufgemacht und dir die Platine bzw die Kondensatoren dort drauf mal genau angeguckt???

Du kannst sie ja dann evtl als Defekt verkaufen, zumindest die Fernbedienung ist ja noch ein paar Euros wert, auch das Netzteil kann vllt noch jemand gebrauchen (apropos: hast du da vllt mal ein anderes passendes versucht? Aber ich weiss, Strohhalm)...

Ciao,
DdD.