Tank bleibt bei "Starting..." stehen

[Miky]

Ich kenne das Problem von meiner Tank, leider ohne Lösung. Regelmäßig , aber nicht reproduzierbar ,hängt die Kiste nach Reboot bei starting..... Das einzige was dann hilft ist, die Box über den ein/aus Schalter hinten links aus und SOFORT wieder einzuschalten. Dann bootet sie sicher durch.

[jokel]

würde mal sagen ein log ist besser als kein log ..
zumindest das letzte besser aussah als das davor

@Bualicher .. ich brauche eine neue brille .. ich hatte das ..
viewtopic.php?p=45726#p45726
nur kurz überflogen und am ende des logs gesehen z.b. das

Code: Alles auswählen

2025-09-27 20:02:37.899 [sectionsd] Reading data finished after 19410 ms (106 events) from https://raw.githubusercontent.com/matthuisman/i.mjh.nz/master/PlutoTV/us.xml
2025-09-27 20:02:48.480 [sectionsd]     eitThread: filter 0x4f mask 0xff -> skip sections for table 0x50

und das ..

Code: Alles auswählen

Hier ein Bootlog einer funktionierneden Tank (Eintrag ist auch hier vorhanden):

war bei mir irgendwie untergegangen

und im log hatte ich nur gesehen das via netzwerk was runtergeladen wurde.
deswegen die annahme das dies zu einen speichermangel führen könnte.

zumindest drück ich dir die daumen das mit anschluss einer platte dies eventuell dein problem löst.

[Bualicher]

Hier ein Bootlog mit intern angeschlossener SATA-Platte:

Code: Alles auswählen

Starting Microloader ASM built on окт 08 2015 09:37:26...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Chip: APOLLO
Found External Realtek 8211EG PHY on GMAC0
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
MMC:No device found
BOX MAC OK!
BOX: Type: TANK Rev: 84900104
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 1002 ms since POR
--------------------------------------------------------------------------------
| U-Boot 2009.08-00067-gebbd4b2 (Apr 03 2015 - 16:35:07)               CST HDx |
|------------------------------------------------------------------------------|
| Chipset information                                                          |
| Vendor: NXP       Type: Apollo           Revision: M1        Fuses: 0015726E |
|------------------------------------------------------------------------------|
| Clock information                                                            |
| *** not available yet ***                                                    |
|------------------------------------------------------------------------------|
| Frontpanel information                                                       |
| Vendor: CST       Version: 4.1           Display: OLED (256 x 64 px)         |
|------------------------------------------------------------------------------|
| Memory configuration                                                         |
| Start    | End      | Type    | Description                                  |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 0FFFFFFF | RAM     | System main memory bank #0 (256M)            |
| 20000000 | 2FFFFFFF | RAM     | System main memory bank #1 (256M)            |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K x  64)      |
  *** Warning - bad CRC or SFC, using default environment
| 00000000*| 3FFFFFFF*| NAND    | Toshiba TC58NVG3S0F 8G 3.3V 8-bit            |
|------------------------------------------------------------------------------|
| Network configuration                                                        |
| MAC: LIP 6300                    address: 00-C5-5C-78-86-E5                  |
--------------------------------------------------------------------------------

Hit any key to stop autoboot:  0

SFC read: offset 0x100000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   NI Apollo Kernel
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2971248 Bytes =  2.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.10.93 (neutrino-images@ni-server) (gcc version 6.3.1 20170109 (crosstool-NG crosstool-ng-1.23.0-36-g1dbb06f2-dirty) ) #1 SMP Sat Sep 27 00:44:46 CEST 2025
[    0.000000] CPU: ARMv7 Processor [411fc091] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Entropic Apollo STB Platform with FDT, model: CoolStream HD2 Apollo STB
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Early platform io descriptors mapping...
[    0.000000] PERCPU: Embedded 7 pages/cpu @80910000 s5952 r8192 d14528 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 256MB 256MB = 512MB total
[    0.000000] Memory: 246960k/246960k available, 277328k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x80678dc4   (6596 kB)
[    0.000000]       .init : 0x80679000 - 0x806a8740   ( 190 kB)
[    0.000000]       .data : 0x806aa000 - 0x806ebd60   ( 264 kB)
[    0.000000]        .bss : 0x806ebd60 - 0x80707424   ( 110 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU debugfs-based tracing is enabled.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:388
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] smp_twd: clock not found -2
[    0.000000] Unable to get timer clock. Assuming 50Mhz input clock.
[    0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[    0.000000] stb-timer: system timer (irq = 58, rate 50000000)
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.254807] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    0.342792] pid_max: default: 32768 minimum: 301
[    0.347635] Mount-cache hash table entries: 512
[    0.354193] CPU: Testing write buffer coherency: ok
[    0.359328] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.364975] Setting up static identity map for 0x803dd018 - 0x803dd070
[    0.371531] L310 cache controller enabled
[    0.375452] l2x0: 8 ways, CACHE_ID 0x410004c4, AUX_CTRL 0x32421001, Cache size: 131072 B
[    0.384176] Brought up 1 CPUs
[    0.387055] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[    0.393379] CPU: All CPU(s) started in SVC mode.
[    0.398749] devtmpfs: initialized
[    0.409011] NET: Registered protocol family 16
[    0.414094] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.544297] GMAC0: active interface is 6
[    0.548155] ChipID=0x1 ChipRevID=0x2
[    0.551856] nx_dmac: Registered with 8 channels
[    0.561136] bio: create slab <bio-0> at 0
[    0.565655] GPIO: base febd5000 (phys e06d5000)
[    0.570369] GPIO: base feb69000 (phys e0669000)
[    0.575310] SCSI subsystem initialized
[    0.579428] usbcore: registered new interface driver usbfs
[    0.584908] usbcore: registered new interface driver hub
[    0.590252] usbcore: registered new device driver usb
[    0.595303] pps_core: LinuxPPS API ver. 1 registered
[    0.600184] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.609247] PTP clock support registered
[    0.614966] Switching to clocksource timer_us
[    0.626039] NET: Registered protocol family 2
[    0.631214] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.638240] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.644688] TCP: Hash tables configured (established 4096 bind 4096)
[    0.650999] TCP: reno registered
[    0.654143] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.659960] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.666477] NET: Registered protocol family 1
[    0.671094] RPC: Registered named UNIX socket transport module.
[    0.676908] RPC: Registered udp transport module.
[    0.681606] RPC: Registered tcp transport module.
[    0.686238] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.692810] PM: STB Platform power mgmt initialization.
[    0.818193] cfg80211: Calling CRDA to update world regulatory domain
[    0.825357] bounce pool size: 64 pages
[    0.835214] NFS: Registering the id_resolver key type
[    0.840260] Key type id_resolver registered
[    0.844342] Key type id_legacy registered
[    0.848331] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.854769] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.862144] msgmni has been set to 482
[    0.866867] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.874217] io scheduler noop registered
[    0.878038] io scheduler deadline registered
[    0.882486] io scheduler cfq registered (default)
[    0.887483] e06e2000.serial: ttyS0 at MMIO 0xe06e2000 (irq = 47) is a uart-ip3106
[    0.898889] loop: module loaded
[    0.902439] ahci-stb e0638000.sata: unable to find phy
[    0.907487] SATA: Adjusting los_lvl (rd_val=0x8a46, wr_val=0x8ae6)
[    0.913652] SATA: Adjusting rx_term_en0/1 (rd_val=0x2750275, wr_val=0x2770277)

Also es ändert sich rein gar nichts, wenn etwas am SATA-Eingang hängt.

[jokel]

das ist nicht schön .. vllt. hat der controller durch den blitzeinschlag ein weg bekommen.
ist das die box ..
https://wiki.tuxbox-neutrino.org/wiki/H ... tream:TANK

theoretisch könnte man ein image bauen und den ganzen scsi krempel mal deaktivieren in ..
https://github.com/neutrino-images/ni-b ... onfig#L983

aber damit kennen sich andere besser aus

wenn das die box von oben ist .. hat die box wohl 3 anschlussmöglichkeiten einer platte ..
intern Sata 3,5"
extern über eSata
extern über USB