nachdem ich nach dem lezten Update immer wieder nach ein paar Stunden eine eingefrorene Box hatte, wollte ich ergründen, ob es mit einer älteren Version genauso ist, oder ein Hardwaredefekt vorliegt.
Der Versuch mit einem offline Update aus dem TEMP-Ordner schlug jedoch leider fehl.
Seitdem hängt die Box beim booten beim NI Logo fest.
Hier habe ich mal das bootlog von einem Versuch, die BOX mit CST Emergency Flash Image wiederherszustellen angehängt denn auch das funktioniert nicht.
- [+] Spoiler
Starting Microloader ASM built on окт 08 2015 10:29:32...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Starting Microloader C...
Chip: KRONOS
Found Internal MYSTI110 PHY on GMAC0
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
BOX MAC OK!
BOX: Type: TRINITY V2 Rev: 7550C100
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 569 ms since POR
--------------------------------------------------------------------------------
| U-Boot 2009.08-00067-gebbd4b2 (Apr 03 2015 - 16:38:15) CST HDx |
|------------------------------------------------------------------------------|
| Chipset information |
| Vendor: Entropic Type: KRONOS Revision: B0 Fuses: 00010001 |
|------------------------------------------------------------------------------|
| Clock information |
| *** not available yet *** |
|------------------------------------------------------------------------------|
| Frontpanel information |
| *** Warning: unexpected answer from Frontpanel *** |
|------------------------------------------------------------------------------|
| Memory configuration |
| Start | End | Type | Description |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 1FFFFFFF | RAM | System main memory bank #0 (512M) |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 ( 4M / 64K x 64) |
*** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND | Toshiba NAND 512MiB 3,3V 8-bit |
|------------------------------------------------------------------------------|
| Network configuration |
| MAC: LIP 6300 address: 00-C5-5C-6C-9B-AB |
--------------------------------------------------------------------------------
Hit any key to stop autoboot: 0
SFC read: offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: NI Kronos Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2907033 Bytes = 2.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.10.93 (neutrino-images@nisrv) (gcc version 6.3.1 20170109 (crosstool-NG crosstool-ng-1.23.0-36-g1dbb06f2-dirty) ) #1 SMP Wed Dec 28 01:10:04 CET 2022
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Entropic Kronos STB Platform with FDT, model: CoolStream HD2 Kronos STB
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Early platform io descriptors mapping...
[ 0.000000] PERCPU: Embedded 7 pages/cpu @80d9a000 s5952 r8192 d14528 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 247128k/247128k available, 277160k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x8065b55c (6478 kB)
[ 0.000000] .init : 0x8065c000 - 0x8068a740 ( 186 kB)
[ 0.000000] .data : 0x8068c000 - 0x806cce00 ( 260 kB)
[ 0.000000] .bss : 0x806cce00 - 0x806e72a4 ( 106 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:350
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] Cortex A9 frequency at 600 MHz
[ 0.000000] Initializing Cortex A9 Global Timer at Vir:0xFEA00200, using, at Freq:300 MHz
[ 0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 14316ms
[ 0.000000] smp_twd: clock not found -2
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.253741] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 0.342750] pid_max: default: 32768 minimum: 301
[ 0.347562] Mount-cache hash table entries: 512
[ 0.354048] CPU: Testing write buffer coherency: ok
[ 0.359140] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.364763] Setting up static identity map for 0x803c61b0 - 0x803c6208
[ 0.371293] L310 cache controller enabled
[ 0.375211] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x32421001, Cache size: 131072 B
[ 0.383838] Brought up 1 CPUs
[ 0.386710] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[ 0.393033] CPU: All CPU(s) started in SVC mode.
[ 0.398307] devtmpfs: initialized
[ 0.406431] NET: Registered protocol family 16
[ 0.411546] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.520127] GMAC0: active interface is 1
[ 0.523985] ChipID=0x1000 ChipRevID=0x100
[ 0.528031] nx_dmac: Registered with 8 channels
[ 0.537024] bio: create slab <bio-0> at 0
[ 0.541548] GPIO: base febab000 (phys e06ab000)
[ 0.546157] GPIO: base feb69000 (phys e0669000)
[ 0.551024] SCSI subsystem initialized
[ 0.555084] usbcore: registered new interface driver usbfs
[ 0.560544] usbcore: registered new interface driver hub
[ 0.565871] usbcore: registered new device driver usb
[ 0.570923] pps_core: LinuxPPS API ver. 1 registered
[ 0.575785] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.584886] PTP clock support registered
[ 0.590447] Switching to clocksource arm_global_timer
[ 0.602080] NET: Registered protocol family 2
[ 0.607149] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.614217] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.620643] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.626960] TCP: reno registered
[ 0.630115] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.635898] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.642383] NET: Registered protocol family 1
[ 0.646942] RPC: Registered named UNIX socket transport module.
[ 0.652793] RPC: Registered udp transport module.
[ 0.657424] RPC: Registered tcp transport module.
[ 0.662099] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.668647] PM: STB Platform power mgmt initialization.
[ 0.782726] cfg80211: Calling CRDA to update world regulatory domain
[ 0.794614] NFS: Registering the id_resolver key type
[ 0.799597] Key type id_resolver registered
[ 0.803746] Key type id_legacy registered
[ 0.807697] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.814102] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.821435] msgmni has been set to 482
[ 0.826051] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.833392] io scheduler noop registered
[ 0.837223] io scheduler deadline registered
[ 0.841607] io scheduler cfq registered (default)
[ 0.846582] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47) is a uart-ip3106
[ 0.857863] loop: module loaded
[ 0.861345] ahci-stb e0638000.sata: unable to find phy
[ 0.866394] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x5711a5)
[ 0.872896] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x277)
[ 0.878945] ahci-stb e0638000.sata: SSS flag set, parallel bus scan disabled
[ 0.885971] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 0.894756] ahci-stb e0638000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[ 0.904218] ata4294967295: SATA PHY offline
[ 0.908785] scsi0 : ahci_platform
[ 0.912330] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe0638fff] port 0x100 irq 39
[ 0.920880] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[ 0.933268] Bad block table found at page 262080, version 0x01
[ 0.939782] Bad block table found at page 262016, version 0x01
[ 0.946069] 3 cmdlinepart partitions found on MTD device e0631000.flash_nand
[ 0.953017] Creating 3 MTD partitions on "e0631000.flash_nand":
[ 0.958879] 0x000000000000-0x000010000000 : "root0"
[ 0.964774] 0x000010000000-0x000012000000 : "var"
[ 0.970170] 0x000012000000-0x000020000000 : "root1"
[ 0.977648] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
[ 0.983436] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
[ 0.989010] 5 cmdlinepart partitions found on MTD device e0632000.flash_sfc
[ 0.995917] Creating 5 MTD partitions on "e0632000.flash_sfc":
[ 1.001716] 0x000000000000-0x000000040000 : "uldr"
[ 1.007371] 0x000000040000-0x0000000c0000 : "u-boot"
[ 1.013077] 0x0000000c0000-0x0000000e0000 : "env"
[ 1.018454] 0x0000000e0000-0x000000100000 : "spare"
[ 1.024096] 0x000000100000-0x000000400000 : "kernel"
[ 1.029851] tun: Universal TUN/TAP device driver, 1.6
[ 1.034835] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.041240] DWMAC1000
[ 1.043512] stmmac - user ID: 0x36, Synopsys ID: 0x36
[ 1.048521] Ring mode enabled
[ 1.051573] DMA HW capability register supported
[ 1.056039] Enhanced/Alternate descriptors
[ 1.060380] Enabled extended descriptors
[ 1.064334] RX Checksum Offload Engine supported (type 2)
[ 1.069775] TX Checksum insertion supported
[ 1.074020] Wake-Up On Lan supported
[ 1.077679] Enable RX Mitigation via HW Watchdog Timer
[ 1.093067] libphy: stmmac: probed
[ 1.096386] eth%d: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) active
[ 1.102826] eth%d: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[ 1.108565] eth%d: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[ 1.114365] eth%d: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[ 1.120150] eth%d: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[ 1.125931] eth%d: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[ 1.131726] eth%d: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[ 1.137508] eth%d: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[ 1.143303] eth%d: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[ 1.149086] eth%d: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[ 1.154881] eth%d: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[ 1.160755] eth%d: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[ 1.166625] eth%d: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[ 1.172511] eth%d: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[ 1.178375] eth%d: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[ 1.184257] eth%d: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[ 1.190131] eth%d: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[ 1.196001] eth%d: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[ 1.201882] eth%d: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[ 1.207751] eth%d: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[ 1.213632] eth%d: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[ 1.219502] eth%d: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[ 1.225382] eth%d: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[ 1.231258] eth%d: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[ 1.237127] eth%d: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[ 1.243008] eth%d: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[ 1.248877] eth%d: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[ 1.254758] eth%d: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[ 1.260634] eth%d: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[ 1.266503] eth%d: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[ 1.272384] eth%d: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[ 1.278253] eth%d: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
[ 1.284615] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.291056] ehci-platform: EHCI generic platform driver
[ 1.296318] ehci-platform e066c000.usb: EHCI Host Controller
[ 1.301912] ehci-platform e066c000.usb: new USB bus registered, assigned bus number 1
[ 1.309764] ehci-platform e066c000.usb: irq 93, io mem 0xe066c000
[ 1.330097] ehci-platform e066c000.usb: USB 2.0 started, EHCI 1.00
[ 1.336242] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.342967] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.350119] usb usb1: Product: EHCI Host Controller
[ 1.354927] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
[ 1.360394] usb usb1: SerialNumber: e066c000.usb
[ 1.365545] hub 1-0:1.0: USB hub found
[ 1.369212] hub 1-0:1.0: 1 port detected
[ 1.373366] ehci-platform e066d000.usb: EHCI Host Controller
[ 1.378938] ehci-platform e066d000.usb: new USB bus registered, assigned bus number 2
[ 1.386848] ehci-platform e066d000.usb: irq 94, io mem 0xe066d000
[ 1.410055] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1.00
[ 1.416206] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.422897] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.430065] usb usb2: Product: EHCI Host Controller
[ 1.434890] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
[ 1.440341] usb usb2: SerialNumber: e066d000.usb
[ 1.444980] ata1: SATA PHY offline
[ 1.448303] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.454134] hub 2-0:1.0: USB hub found
[ 1.457798] hub 2-0:1.0: 1 port detected
[ 1.462057] usbcore: registered new interface driver usb-storage
[ 1.468095] usbcore: registered new interface driver usbserial
[ 1.474404] usbcore: registered new interface driver usbhid
[ 1.479874] usbhid: USB HID core driver
[ 1.483946] TCP: cubic registered
[ 1.487171] NET: Registered protocol family 17
[ 1.491772] Key type dns_resolver registered
[ 1.496049] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 3
[ 1.503614] ThumbEE CPU extension supported.
[ 1.508480] ### dt-test ### No testcase data in device tree; not running tests
[ 1.990059] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 2.155470] usb 2-1: New USB device found, idVendor=26bd, idProduct=9917
[ 2.162102] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.169153] usb 2-1: Product: USB DISK 2.0
[ 2.173222] usb 2-1: Manufacturer:
[ 2.177361] usb 2-1: SerialNumber: 07085A366320BD47
[ 2.182918] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 2.189168] scsi1 : usb-storage 2-1:1.0
[ 3.192437] scsi 1:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 6
[ 3.201173] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 4.207382] jffs2: Empty flash at 0x07a7f1ec ends at 0x07a7f800
[ 4.690898] sd 1:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[ 4.700641] sd 1:0:0:0: [sda] Write Protect is off
[ 4.707123] sd 1:0:0:0: [sda] No Caching mode page found
[ 4.712378] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 4.728246] sd 1:0:0:0: [sda] No Caching mode page found
[ 4.733499] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 4.742658] sda: sda1
[ 4.753132] sd 1:0:0:0: [sda] No Caching mode page found
[ 4.758360] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 4.764435] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 7.200264] VFS: Mounted root (jffs2 filesystem) on device 31:0.
[ 7.206191] devtmpfs: error mounting -2
[ 7.210284] Freeing unused kernel memory: 184K
[ 7.214687] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 7.226987] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.93 #1
[ 7.232986] [<800140d0>] (unwind_backtrace+0x0/0xe8) from [<800111bc>] (show_stack+0x10/0x14)
[ 7.241431] [<800111bc>] (show_stack+0x10/0x14) from [<803bcfec>] (panic+0xa0/0x1ec)
[ 7.249111] [<803bcfec>] (panic+0xa0/0x1ec) from [<803b8550>] (kernel_init+0x14c/0x150)
[ 7.257059] [<803b8550>] (kernel_init+0x14c/0x150) from [<8000dae0>] (ret_from_fork+0x14/0x34)
MfG und guten Rutsch und ein erfolgreiches, gesundes 2023
